Cloudflare Tunnel Inside MikroTik — No Dedicated Proxy VM Needed

Cloudflare Tunnel gives you a secure outbound-only connection from your homelab to Cloudflare’s edge, proxying public traffic without opening any firewall ports. No pinholes, no DMZ, no exposing your home IP. The usual deployment is a Docker container or a systemd service on a Linux box. But if you have a MikroTik router running RouterOS 7.6+ with container support, you can run cloudflared directly on the router — zero extra hardware, zero extra VMs. ...

May 8, 2026 · 9 min · 1707 words · GnTech

MikroTik WireGuard — Site-to-Site and Road Warrior VPN Setup

WireGuard on MikroTik RouterOS is production-ready as of RouterOS 7.x, and it’s dramatically simpler than IPsec or OpenVPN for homelab use. No certificate authorities, no confusing phase 1/phase 2 settings, no userspace daemon eating CPU — just a kernel module, a private key, and a peer config. This post covers two WireGuard topologies running on the same MikroTik router (R1 from the previous deployment post): Road Warrior — remote devices (phone, laptop) connect to the homelab Site-to-Site — two MikroTik routers connected across the internet Both share the same base config and coexist on the same router. ...

May 8, 2026 · 14 min · 2913 words · GnTech

Proxmox Networking — Bridges, VLANs, and a Clean Host Topology

A Proxmox bridge connects guest interfaces to a network. VLAN filtering determines which VLANs traverse its ports. Routing and firewall policy determine which subnets may communicate. Start by documenting what the physical switch sends to the host. A correct guest VLAN tag cannot fix a mismatch on the uplink. Verification status Area Evidence and limits Technical review Reviewed against the official references below on October 31, 2026. Shell examples Bash syntax checked; no host networking commands executed. Configuration Illustrative single-uplink IPv4 lab, not a captured production configuration. Runtime Application, rollback, DHCP, guest traffic, and firewall behavior remain untested for this revision. 1. Identify the management path These two designs are different: ...

May 8, 2026 · 5 min · 1061 words · GnTech

Building R1 — A MikroTik Router for VLAN-Segmented Homelab

Every homelab needs a solid network foundation. This guide walks through the full configuration of R1 — a MikroTik edge router with segmented VLANs, inter-VLAN firewalling, WireGuard VPN, and a Cloudflare Tunnel running directly on the router. The config below is based on RouterOS 7.22.1. Commands are split by section so you can follow along step-by-step. Replace anything in <> with your own values. Hardware Model: MikroTik E62iUGS-2axD5axT OS: RouterOS 7.22.1 WAN: GPON FTTH (PPPoE on VLAN 100) Port Layout Port Role Access VLAN Notes SFP1 WAN — GPON ONT, native vlan 1 for ONT access Ether1 CCTV 50 Untagged, camera network Ether2 MGMT 99 Untagged, management Ether3 MGMT 99 Untagged, secondary management Ether4 HOME 10 Untagged, main home LAN Ether5 Trunk Tagged Inter-switch link carrying all VLANs Step 1 — Bridge Setup Create the main bridge with VLAN filtering enabled, and a separate bridge for container veth interfaces: ...

May 7, 2026 · 11 min · 2282 words · GnTech

Deploying Frigate NVR on Proxmox — Tapo C100, OpenVINO, and Telegram Alerts

Historical setup: This article records the original lab deployment. Frigate configuration changes between releases; validate the configuration against the documentation for the exact image version you deploy. The example exposes several service ports and is intended for an isolated lab network. Restrict access at the host and router, and use the authenticated interface supported by your chosen release. Frigate is an open-source NVR built for real-time object detection with local processing. No cloud subscriptions, no vendor lock-in — just cameras, a GPU, and decent detection models. ...

May 7, 2026 · 6 min · 1186 words · GnTech

Hello, World

Welcome to the blog. This is where I’ll be writing about homelab stuff — Proxmox, MikroTik, Docker, networking, automation, and whatever else I’m tinkering with. Stay tuned.

May 6, 2026 · 1 min · 27 words · GnTech